Search

Let it Snow Christmas Tag


All images © 2016-2019 Stampin’ Up!®

Supply List:

  • Let it Snow Suite [153386]

  • Snowman Season Bundle [152337]

  • (Snowman Season Stamp Set & Snowman Builder Punch)

  • Let It Snow Speciality Designer Series Paper (SDSP) [150393]

  • Blueberry Bushel Cardstock [146968]

  • Early Espresso Cardstock [119686]

  • Whisper White Cardstock [100730]

  • Real Red Ink Pad [147084]

  • Winter Knit 3D Embossing Folder [150645]

  • Real Red Glimmer Paper [150427]

  • Real Red Curly Ribbon [150426]

  • Let it Snow Embellishment Kit [150425]

  • Wink of Stella Glitter Brush [141897]

  • Scalloped Tag Topper [133324]

  • Mini Glue Dots [103683]

  • Take Your Pick Tool [144107]

  • Multipurpose Liquid Glue (Tombow) [110755]

  • Stampin' Dimensionals [104430]

Measurements:

  • Blueberry Bushel Cardstock 2” x 5 1/2” and 1/2” x 2”

  • Let it Snow Speciality Designer Series Paper 1 3/4” x 3” and 1 3/4” x 1 1/2”

  • Whisper White Cardstock 1 3/4” x 4” and 1” x 4”

Directions:

Tag Base:

1. Cut Blueberry Bushel Cardstock 2” x 5 1/2”

2. Emboss with Winter Knit 3D Embossing Folder

3. Punch top with Scalloped Tag Topper Punch

4. Fold 7” Ribbon in half, thread through Tag front, loop & tie

Tag Front:

1. Cut SDSP 1 3/4” x 3”

2. Cut the same SDSP 1 3/4” V x 1 1/2” H & adhere the back side to bottom edge of first DSP with Tombow

3. Center on Tag Base & adhere with Tombow

4. Cut Blueberry Bushel Cardstock strip 1/2” x 2”;

adhere over edge where the two pieces of DSP meet with Tombow

Snowman:

1. Stamp Snowman at the base of a 1 3/4” x 4” Whisper White Cardstock in Memento

Black Ink

(Tip: there is only one Snowman in the Stamp Set that coordinates with the Punch)

2. Punch out with Snowman Builder Punch

(Tip: you can punch the glittery Snowman from the SDSP with the Punch)

3. Punch Hands from Early Espresso Cardstock & adhere to Snowman with Mini Glue Dots

(Technique Tip: How to Roll Mini Glue Dots to adhere Small Images:

Place the piercing end of your Take Your Pick Tool directly onto a Mini Glue Dot, roll in a circular motion, lift with the Tool & adhere to image)

4. Punch Hat from Real Red Glimmer Paper; add a strip of Washi Tape cut in half,

along with a Black enamel shape; adhere Hat to Snowman with Mini Glue Dots

5. Line up the middle of Snowman on the Blueberry Bushel Cardstock strip & adhere

with Stampin’ Dimensionals

6. Add Wink of Stella to Snowman

Greeting:

1. Cut Whisper White Cardstock 1” x 4”

2. Stamp ‘Merry Christmas’ in Real Red Ink

3. Cut between Merry & Christmas separating words & Fussy Cut both words

4. Adhere to Tag with Stampin’ Dimensionals


0 views

Kathy W. McDaniel. All Rights Reserved - Images © 2020 - 2016 Stamping' Up! ® 

Kathy W. McDaniel is an Independent Stamping' Up! Demonstrator and is responsible for the content of this website.